The 10 Most Terrifying Things About Car Key Button Repair

Car Key Button Repair

A broken car key button can be a hassle. You might need to call an emergency car key repair locksmith service that is available 24 hours a day for assistance or purchase a replacement remote.

You could save money by repairing your old key fob rather than replacing it. This is especially true if the issue is caused by an old switch or a damaged contact.

Battery

If the buttons on the key fob aren't responding to pressing the buttons, it could be an obvious indication that the battery is dying or nearing the end of its lifespan. It's easy to replace the battery on your own instead of paying locksmiths or dealers.

First, locate the battery compartment. The battery compartment is usually located on the back of the key fob and is often hidden behind a cover that opens or a button that opens the access point. Once the compartment is exposed you can see the small button cell battery. It is usually shaped like an oblong coin and is has a plus and minus sign. Remove the battery that is old, and replace it with a new one. Make sure the plus and minus symbols are aligned correctly.

Once the battery is installed Close the compartment and snap the two parts of the key fob. Make sure you align the two pieces and snap them in place properly prior to closing the door and testing your keys. Press any of the buttons to verify that they work properly.

If your remote key repair near me key fob ceases functioning even after replacing the battery, it might be suffering from other issues that require a different type of repair. Damage to the physical structure caused by dropping the fob into a puddle, for instance could cause it to stop functioning altogether. It could also be a problem with the internal electrical system, or it may need to be deprogrammed. Find out if the problem is with your key fob by applying these other typical automotive troubleshooting methods.

Switches

Based on the year and manufacturer, there are various types of switches that are used in the car keyfob. The older style key is equipped with an embedded chip that can be seen inside the case. The newer keys work by transmitting signals to your car. The keys' buttons can be worn out or damaged through normal use, regardless of the model. This causes them to become difficult to press or even unresponsive. If you attempt to force the button to work it could cause further damage, and could even prevent the key from starting your vehicle in the future.

If your key doesn't appear to be working, first try changing the battery. If it doesn't work, you might have to clean your key fob or re-adjust the switches. Since these tiny electronic switches are constantly being moved around and tangled, they are more likely to break down than the larger components of your key.

The switches feel rubbery and are coated with a film that conducts electricity. This film can fade over time. Fortunately, they're tiny and inexpensive to replace. The old ones are soldered to the circuit board, and you'll have to take care to remove them without causing any damage to anything else. Then, you can solder the new ones in and rebuild your key fob.

A good way to keep your car key fob from getting ruined is to avoid using it for more than a few hours at a stretch, and to avoid leaving it in visible locations where it can be seen. If you don't use your key, put it away in a secure place.

If the issue continues to persist after you've cleaned your key fob or battery, and tried to clean it, then you may need to talk to an expert locksmith. A professional locksmith can check the frequency of your key to determine if your vehicle is still able to communicate. They can also open and replace microswitches, alter cases, and much more.

Outer Case

If the buttons can't move freely up and down the case, they could become stuck or break. If changing the battery or cleaning with a cotton swab and some rubbing alcohol don't resolve the problem, removing the case and inspecting could be required. If the contacts the buttons touch are not suitable for the application, or if they are worn, adjusting them may be the only solution.

Certain keys have buttons made of rubber, which wear away over time. The buttons made of rubber can become difficult to press because they stretch, and nails could gouge them. This could cause the key to fail and in this instance it is time for an entirely new case or buttons. This repair involves taking apart your remote, finding the switch on the board, then heating the solder, and carefully taking them off. The circuit board is soldered with new buttons. The case can be reassembled, and the key blade of the horseshoe can be attached. The new buttons should be fitted snugly into the case to prevent them from falling out.

Inner Case

Since your key fob is likely to be tossed around and sometimes be accidentally pressed and the buttons inside may get damaged or stuck over time. Utilizing metal tape and a hole-punch, you can usually solve this issue in the event your car key fob repair service is not at home and the key fob won't work, allowing you to unlock the doors, but not to start the engine. This simple fix will allow you to safely get back to your vehicle and complete your journey.